HP各种机型面板信息汇总(9)

RFU LOAD ERROR An error has occurred during a firmware upgrade.

Reinstall the firmware.

Scanner Bulb Failure (HP LaserJet 3052/3055 all-in-one only)

The scanner assembly experienced a scanner-bulb error.

Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize.

Try another power source.

If the error persists, lift the flatbed to see if the scanner bulb is illuminating. If it is not illuminating, replace the scanner assembly.

See Scanner assembly on page 148.

If the bulb is illuminating, the scan module might be too far to the right to find the calibration strip during startup. Use the following procedure to move the scan module so it begins the startup cycle farther to the left: 1.

Cycle the power and watch the movement of the scan module. The scan module moves to the left and the bulb illuminates. When it does, cycle the power again. 2.

Repeat the first step until the scan module is about 3 centimeters (about 1 inch) from the right edge of the scan glass.

3. Turn on power by using the power switch. If the error persists, replace the scanner assembly.

Scanner Error [#] Turn off then on (HP LaserJet 3052/3055 all-in-one only)

1 = DarkFind 2 = LMWTempFind 3 = BulbWarmupFromOff 4 = BulbWarmupFromCoarse 5 = CalLabelFind 6 = DocOriginFind 7 = LMWFinalFind

8 = CalLabelFindAfterScan 9 = CalLabelFindPriorToStandby 10 = DocOriginFindPriorToStandby 11 = BulbWarmupFromStandby

1. 2.

Power cycle the all-in-one. If the error persists, replace the scanning assembly. See for information about replacing the HP LaserJet 3052/3055 all-in-one scanning assembly.

3. If the error persists, replace the formatter. See Formatter and line interface unit (LIU) on page 178.

Scanner reserved for PC scan A computer is using the all-in-one to create a scan.

Wait until the computer scan has finished, or cancel the scan from the computer software, or press Cancel.

第 41 页 共 43 页

Scanning error Cannot connect The all-in-one cannot transmit scan information to Verify that the connection cable is not loose a computer.

or damaged. Replace the cable if necessary, and try the scan again.

Settings cleared The all-in-one has cleared job settings. Re-enter any appropriate job settings.

Setting saved

SIZE MISMATCH IN TRAY XX alternates with Ready

A menu selection has been saved. No action necessary.

Make sure that the media guides are adjusted correctly.

In the PAPER HANDLING menu, configure the tray for the correct size.

The tray is loaded with a media size that is 1. different from the size for which the tray is configured. Printing can continue from other 2. trays, but not from this one.

Sleep mode on The printer is in the sleep mode. Any button No action necessary. The printer press or the receipt of data clears the sleep automatically exits sleep mode. mode.

Standard output bin full Remove all paper from bin

The top (standard) output bin is full and must 1. be emptied.

2.

Empty the top output bin. If the error persists, verify that the output-bin sensor (PS104) is operating and that the sensor arm can freely move.

See Printer switches and sensors.

STANDARD TOP BIN FULL alternates with

Remove all paper from bin To return to ready press STOP

The output bin is full. Printing cannot continue.

Empty the output bin. Printing resumes automatically.

The printer is paused and no error messages No action necessary. are pending.

TRAY OVERFILLED REMOVE EXCESS PAPER

The tray is loaded with too much media. 1. 2. 3.

Press ▼to see step-by-step information.

Remove excess media. Press？ to exit.

Tray X alternates with

To change size or type press√

The printer is reporting the current configuration of tray X.

No action necessary. Press

to clear the message.

Press√ to change the type or size.

TRAY XX EMPTY alternates with

TRAY XX OPEN For help press alternates with

TYPE MISMATCH IN TRAY XX alternates with Ready

The tray is loaded with a media type that is In the PAPER HANDLING menu, configure different from the type for which the tray is the tray to match the type. configured. Printing can continue from other trays.

第 42 页 共 43 页

The tray is open, but printing can continue. Close the tray.

The tray is empty, but the current print job Fill the tray. The message indicates does not require this tray.

the type and size of media for the tray.

Unauthorized supply in use alternates with Ready

The printer has detected that a non-HP supply If you believe you purchased an HP is currently installed and √ was pressed. supply, go to

www.hp.com/go/anticounterfeit. Service or repairs required as a result of using non-HP supplies are not covered under HP warranty.

Unexpected size in tray X

Unexpected paper size error. The media size loaded Verify that the print settings are set to the in the tray does not match the media size configured for the tray.

specified media in the tray.

WAIT FOR PRINTER TO REINITIALIZE The printer is reinitializing. 打印多份，会不停重复打印。

维修代码:

Printer model PIN code 3005: 10300506 3500: 03350006 4200: 02420004 4250: 09425004 4300: 11430002 4350: 09435004 4600: 02460004 4700: 06470005 5200: 05520006 9000: 00900001

1. 网卡问题，网卡与机型不兼容 2. 驱动问题，重新下载驱动安装。

No action necessary.

第 43 页 共 43 页