HP各种机型面板信息汇总(6)

door open detection switch actuator. The connector in the +24VB line is not properly connected.

Defective front door detection switch. Defective DC controller PCB.

2. Replace the door open detection switch actuator (the switch arm for the front cover and right frame).

3. 4. 5.

Reseat the DC controller PCB connector J1010.

Replace the door open switch. Replace the DC controller PCB.

CLOSE REAR BIN The rear door is open after creating a cleaning page.

Close the rear door.

CLOSE TOP COVER AND FRONT DOOR The top cover and front door need to be

closed.

CODE CRC ERROR

An error has occurred during a firmware upgrade.

Comm. error

A fax communication error occurred between the all-in-one and the sender or receiver.

Close the top cover and front door.

Reinstall the firmware.

Allow the all-in-one to retry sending the fax. Unplug the all-inone telephone cord from the wall, plug in a telephone, and try making a call. Plug the all-in-one telephone cord into a jack for another phone line. Try a different telephone cord.

Creating...CLEANING PAGE The printer is generating a cleaning page. 1. The printer returns to the Ready state after. 2.

3. 4.

Load the cleaning page into tray 1. Press Menu.

Select PRINT QUALITY, and then press√.

Select PROCESS CLEANING PAGE,and then press√ .

DATA RECEIVED The printer received data and is waiting for If the printer is waiting for a form a form feed. The message disappears when the feed,Press√ to continue. printer receives another file. The printer is paused.

If the printer is paused, press Stop to continue.

Date/Time=[YYYY]/[MMM]/[DD] [HH]: [mm]

The printer has an internal clock that tracks Press√ to change the date and time. the date and time.

Press Stop to skip this step. You can set the date and time later by using the SYSTEM SETUP menu. Press ? to exit.

Deleting Private Jobs The printer is in the process of deleting a No action necessary. private job.

Deleting... The printer is in the process of deleting a No action necessary. job.

Device error Press √

Device is busy. Try again later

An internal error occurred in the device. The all-in-one is currently in use.

Press √ (Select) to resume the job. Wait for the all-in-one to finish the current job.

Doc feeder jam Clear, Reload A piece of media is jammed in the ADF tray. Open the document release door, clear the jam, close the document release door, and

第 26 页 共 43 页

reload the paper into the ADF tray.

Document feeder mispick. Reload Door open

The printer door is open.

Media in the ADF tray was not picked up.

Remove the media from the ADF tray, and then reload it.

The door must be closed before printing can continue.

Duplexer Error Remove Duplexer The duplexer has been removed.

Duplexing is not available for the HP laserJet 5200L.

Duplexing...Do not grab paper

1. 2. 3.

Turn the printer off. Reinstall the duplexer. Turn the printer on.

During duplex printing, the paper emerges for No action necessary. a short time before it is pulled back into the Printer. Duplexing is not available for the HP LaserJet 5200L.

EIO Disk Not Functional The EIO disk in slot is not working correctly.

1. 2. 3.

Press▼ to see step-by-step information.

Turn the printer off. Remove the EIO disk from the indicated slot and replace it with a new disk.

4.

EIO Disk Spinning Up

Press? to exit.

The EIO disk device in slot is spinning No action necessary. up its platter. The message appears for approximately 15 seconds after the printer exits PowerSave mode, and jobs that require disk access will be delayed.

Engine comm. error The device experienced an internal communication This is a warning message only. Job output error.

might be affected.

Event Log Empty SHOW EVENT LOG was selected from the control No action necessary. panel, and the event log is empty.

External Accessory Not Supported Indicates that the external duplexer or 500- 1.

sheet feeder is disabled because it does not support the external accessory.

2. 3.

Fax delayed – Send memory full

Fax memory is full.

Press▼ to see step-by-step information.

Remove the duplexer or 500-sheet feeder.

Press ? to exit.

Cancel the fax by pressing or Cancel. Resend the fax. You might need to send the fax in multiple sections if the error occurs again.

Fax is busy Canceled send The fax line to which you were sending a fax was Call the recipient to ensure that the fax busy. The allin-one has canceled sending the fax. machine is on and ready.

Check that you are dialing the correct fax number.

Check that the Redial if busy option is enabled.

Check for a dial tone on the phone line by

第 27 页 共 43 页

pressing Start Fax.

Make sure that the phone is working by disconnecting the allin-one, plugging in a telephone to the phone line, and making a voice call.

Plug the all-in-one telephone cord into a jack for another phone line, and then try sending the fax again.

Try a different telephone cord.

Fax is busy Redial pending

The fax line to which you were sending a fax was Allow the all-in-one to retry sending the busy. The allin-one automatically redials the busy number.

fax.

Call the recipient to ensure that the fax machine is on and ready.

Check that you are dialing the correct fax number.

Check for a dial tone on the phone line by pressing Start Fax.

Make sure that the phone is working by disconnecting the allin-one, plugging in a telephone to the phone line, and making a voice call.

…… 此处隐藏：8432字，全部文档内容请下载后查看。喜欢就下载吧 ……