HP各种机型面板信息汇总(5)

59.C0 Error on control panel 59.12.00 (event log only)

An error occurred in the developing engaging mechanism. 1.

The movement of the developing engaging lever is not smooth. Make the movement of the lever smooth. Replace the gear for the lever, if damaged. 2.

Damage on the drive gears. Check each drive gear between the delivery motor and the developing engaging clutch. Replace any, if damaged. 3.

Faulty developing engaging sensor lever Reseat the developing engaging sensor lever to the correct position if its movement is not smooth or it is out of position. Replace the lever if it is damaged or deformed. 4.

Faulty developing engaging sensor. Replace the developing engaging sensor. 5.

The connectors in the developing engaging clutch drive signal line are not connected properly. Reseat the connectors J5014 and J1019 between the developing engaging clutch and the DC controller PCB. 6.

The connectors in the delivery motor drive signal line are not connected properly.Reseat the connectors J5004 and J1016 between the delivery motor and the DC controller PCB. 7.

Faulty developing engaging clutch.Replace the developing engaging clutch. 8. 9.

Faulty delivery motor. Replace the delivery motor

Faulty DC controller PCB. Replace the DC controller PCB.

62.* PRINTER ERROR

打印機內存錯誤,*值表示如下:

1.

重新安裝插入的內存；

第 21 页 共 43 页

0=內部內存 1-3=DIMM插槽1-3

64 PRINTER ERROR

接受數據緩衝錯誤

2. 3. 1. 2. 3.

交換安裝位置； 更換插入的內存 重新啟動打印機； 更換接口板

HP 3700 only - replace the firmware

DIMM.

66 xx.yy PRINTER ERROR

外部送紙錯誤,XY描述如下1stX=使用的設備編號2ndX=設備類型: a) 輸入設備 b) 輸出設備

c) 分裝/裝訂設備yy=錯誤設備的編號

68 NVRAM ERROR CHECK SETTINGS

An error occurred in the printer’s nonvolatile memory (NVRAM) and one or more printer settings has been reset to its factory default.

2. 3. 1.

Print a configuration page and check the printer settings to determine which values have changed.

Remove EIO card. It will be reset if not removed.

Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used.

68 NVRAM FULL CHECK SETTINGS

The printer’s nonvolatile memory (NVRAM) is 1. full. Some settings might have been reset to the factory defaults.

2. 3.

Print a configuration page and check the printer settings to determine which values have changed.

Remove EIO card. It will be reset if not removed.

Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used.

68.X PERMANENT STORAGE FULL

A non-volatile storage device is full. Press 1. √ to clear the message. Printing can continue, but unexpected behavior could result. X Description: 0 Onboard NVRAM

1 Removable disk (flash or hard)

4. 3. 2.

Press√ to continue.

For 68.0 errors, turn the printer off and then on.

If a 68.0 error persists, contact HP Support.

For 68.1 errors, use the HP Web Jetadmin software to delete files from the disk drive.

68.X PERMANENT STORAGE WRITE FAIL

A non-volatile storage device is full. Press Press √to continue. √ to clear the message. Printing can continue, but unexpected behavior could result.

1. 2. 3.

重新啟動打印機； 檢查所有的連接電纜； 重新安裝外部送紙設備

第 22 页 共 43 页

X Description: 0 Onboard NVRAM 1 Removable disk

68.X STORAGE ERROR SETTINGS CHANGED

A non-volatile storage device is full. Press 1. √ to clear the message. Printing can continue, but unexpected behavior could result. X Description: 0 Onboard NVRAM 1 Removable disk

4.

69.x PRINTER ERROR

A temporary printing error occurred. X Description

0 The duplex mechanism has failed. 1 The duplex slide adjust has failed.

79.xx PRINTER ERROR

打印機檢測到錯誤. XX代表：

00 firmware exception

1 firmware ASIC fault

Press▼ to see step-by-step information.

To clear the error, press√ to exit the message, and then press to continue.

2.

3. If the problem persists, turn the printer off and then on. To exit, press ?.

Turn the printer off, and then turn the printer on. Reseat the duplexer

1. 2.

1. 2. 3. 4. 5. 6. 7.

重新啟動打印機；

判斷所使用的打印軟件是否和打印機相匹配；

更換傳輸電纜和電源； 拆除DIMM

如可能，使用並口傳輸數據； 拆除EIO設備； 更換接口卡

2 Access error 3 Address error 4 Illegal instruction

5 or 6 or 7 Reserved 8 Privilege violation 9 Trace fault

10 Unimplemented line-a opcode

11 Unimplemented line-f opcode

14 Format error

15 Uninitialized interrupt 120 ASIC fault

8X.YYYY EIO ERROR

The EIO accessory card has encountered a critical error.

8X.YYYY EMBEDDED JETDIRECT ERROR 99 ERROR

The HP Jetdirect embedded print server has Turn the printer off and then on. encountered a critical error. (Event log only) RFU (remote firmware upgrade) failed

30016 30017 30035 30036 30108 30109

Insufficient memory Print page punt NVRAM error NVRAM service error MIO connection break Data communication error

Turn the printer off and then on.

Resend firmware upgrade.

第 23 页 共 43 页

30110 35028 35031 50003 50004 50005 50007 50012 50013

FULL

MIO buffer overflow Bad MIO

Invalid personality Bad fuser Bad beam detect Bad scanner motor

Engine-communication error Bad malfunction Laser malfunction

The specified output bin is full but is not Remove the media from the output bin. needed for the cur …… 此处隐藏：7105字，全部文档内容请下载后查看。喜欢就下载吧 ……