HP各种机型面板信息汇总(8)

Incorrect yellow

One of the following messages may display:

Install black cartridge Install cyan cartridge Install magenta cartridge Install yellow cartridge

The supplies gauge will display the consumption levels of print cartridges.

One of the following messages may display: Non HP black installed Non HP cyan installed Non HP magenta installed Non HP yellow installed alternates with To accept Press √

One of the following messages may display: Order black cartridge, Order cyan cartridge, Order magenta cartridge, or Order yellow cartridge alternates with Ready

The supplies gauge will display the consumption levels of print cartridges.

One of the following messages may display:

Replace black cartridge Replace cyan cartridge Replace magenta cartridge Replace yellow cartridge

The cartridge threshold has been reached.

The supply must be replaced before printing can continue.

The print cartridge low threshold has been For more information go to the HP Color reached.

LaserJet 2605 Series toolbox and click Supplies Status. To order supplies online, click Order Supplies.

A non-HP cartridge is installed.

NOTE Any printer repair required as a result of using a non-HP or unauthorized supply is not covered under warranty.

To use this cartridge, override by pressing the (Select) button on the control panel.

The out threshold has been reached.

The supply must be replaced before printing can continue.

第 36 页 共 43 页

One of the following messages may display:

Unauthorized yellow Unauthorized magenta Unauthorized cyan Unauthorized black

Page too complex Press [√ ]

A new supply has been installed that is not made If you believe you purchased an HP supply, by HP. One of these four messages is displayed

please call the HP fraud hotline at

until an HP supply is installed or √(Select) is 1-877-219-3183. Service or repairs required pressed.

as a result of using non-HP supplies is not covered under HP warranty.

To continue printing, press √(Select).

The all-in-one could not print the current page because of its complexity.

Press √to clear the message. Allow the all-in-one to finish the job, or press Cancel to cancel the job.

PAPER PATH JAM FRONT DOOR alternates with For help press ？

PAPER WRAPPED AROUND FUSER

A page is jammed in the paper path. Open the front door and remove any jammed media.

The paper has wrapped around the fuser. This jam does not have a jam code.

1. 2. 3.

Press▼ to see step-by-step information.

Turn off the printer.

If the printer has a duplexer, go to step 4.If the printer does not have a duplexer,go to step 6.

4. 5. 6.

Slide the duplexer out halfway. Open the rear door and remove the duplexer.

Release the fuser NIP by slightly pushing the rear door up and holding the black plastic inside the rear door.

7. Slightly lift up the black plastic until it releases from the rear door, and then push the rear door toward the top of the table.

8. 9.

Open the print-cartridge door and remove the print cartridge. Remove any jammed media. then close the cartridge door.

10. Reinstall the print cartridge and 11. Reinstall the duplexer and close

the rear door. 12. Turn on the printer. 13. Press？ to exit.

Paused alternates with

To return to Ready press the STOP key

perform a cold reset

1. 2.

第 37 页 共 43 页

Turn the printer power off. For HP Laserjet 4200/4300 Series

The printer has paused.

Press Stop to resume printing.

printers: Hold down √( SELECT button), and then turn the printer power on.

For HP Laserjet 4250/4350 Series printers: Turn the printer power on, and then hold down √(SELECT button) when the memory count begins. 3.

Continue holding down√ until all three printer control-panel lights flash once and then remain on. This might take up to 10 seconds. 4.

After the message SELECT LANGUAGE appears on the display, press ▲(UP ARROW button) or▼ (DOWN ARROW button) until COLD RESET is highlighted. 5.

Press √. The printer performs a cold reset and then continues its power-on sequence. 6.

Check all I/O settings and reset any customer-set printer configuration values.

Performing upgrade

A firmware upgrade is in process.

No action necessary. (Do not turn off the printer.)

Performing... PAPER PATH TEST Please Wait PRINTING STOPPED

The printer is performing a paper-path test. No action necessary. The printer is offline.

No action necessary.

This message appears when a Print/Stop test Press √to continue printing. runs and the time expires.

Printing... CONFIGURATION The printer is generating the configuration No action necessary. page. The printer will return to the Ready state after.

Printing... ENGINE TEST Printing... EVENT LOG

The engine-test page is printing. No action necessary.

The printer is generating the event log page. No action necessary. The printer will return to the Ready state after.

Printing... FILE DIRECTORY The printer is generating the mass storage No action necessary. directory page. The printer will return to the Ready state after.

Printing... FONT LIST The printer is generating either the PCL or No action necessary. PS personality typeface list. The printer will return to the Ready state after.

第 38 页 共 43 页

Printing... MENU MAP The printer is generating the printer menu No action necessary. map. The printer will return to the Ready state after.

Printing... REGISTRATION PAGE The printer is generating the registration Follow the instructions on the printed page. The printer will return to the SET RE …… 此处隐藏：7900字，全部文档内容请下载后查看。喜欢就下载吧 ……