HP各种机型面板信息汇总(2)

5. Open the lower rear door completely and remove all media inside.将后门完全打开，取出所有的卡纸

6. Close the rear door. The four tabs in the paper guide automatically reattach to the door. 关上后门，

7. 8.

13.XX.YY JAM INSIDE TOP COVER 顶盖卡纸 alternates with Remove print cartridge 拿出硒鼓

3. 4.

A jam has occurred in the registration assembly area. 登记组件区域卡纸

2. 1.

Reinstall the duplexer. 重装双面器

To exit, press ？.

Press▼ the to see step-by-step information.

Open the top cover and remove the print cartridge. 打开顶盖，取出硒鼓

Remove all media inside. 取出里面的所有卡纸

Lift the metal flap and remove any remaining media.抬起登记组件的铁板，取出剩下的卡纸

5. Verify that the media size matches the tray settings and the dial on the tray. 检查纸张尺寸是否和纸盒的尺寸刻度杆上的刻度匹配

6. Reinstall the print cartridge and close the top cover.装回硒鼓和关闭顶盖

7.

13.1 paper jam或 13.2 paper jam

打印紙在送紙部分被延遲或停止

1. 2. 3.

To exit, press ？. 確定紙盒被正確安裝; 確定送紙部分沒有阻礙物;

檢查PS402、PS403是否正常工作,必要時需更換相關傳感器

13.3 PAPER JAM

CHECK RIGHT DOOR 检查右门 alternates with

THEN OPEN AND CLOSE TOP COVER 打开和关闭顶盖

Paper delay jam. Paper did not reach PS1 at the registration area.

纸张延时卡纸。纸张没有到达登记组件区域的PS1传感器

1. Remove the toner cartridge,lift the green handle, and verify the sensor flag operation.拿出硒鼓，抬起绿色的手柄，验证传感器杆的操作

2. 3.

Make sure that the sensor is not broken. 确认传感器（杆）没有折断 Replace the registration assembly if necessary. See“Registration Assembly” on page 217 for instructions. 有必要的话，更换登记组件。查看“登记组件”在说明书

第 6 页 共 43 页

的第217页。

13.5 paper jam 或13.6 paper jam 打印紙在加熱組件部分被延遲或停止

1. 2. 3.

確定轉印輥和傳送皮帶能正常工作; 確定輸紙路徑沒有阻礙物; 檢查PS1307是否正常工作,必要時需更換此傳感器

13.10 paper jam

打印紙在吸紙區被延遲或卡住

1. 2.

檢查送紙器的送紙部分是否有阻礙物;

檢查送紙器中PS1701、PS1703傳感器是否復位，必要時，更換相關傳感器

13.20 paper jam或13.21 paper jam 打印紙被卡在輸紙路徑上或打印機上蓋被打開

1. 2. 3.

檢查整個輸紙路徑,清除阻礙物; 檢查所有的輸紙部件是否復位(包括上蓋是否蓋上);

檢查輸紙路徑上的所有傳感器是否復位,必要時需更換

13.A PAPER JAM CHECK LEFT DOOR 检查左侧门

13.90.00 JAM INSIDE FRONT DOOR alternates with REMOVE INCOMPATIBLE TRANSPARENCIES

There is a jam inside the front door caused Press? for help. by incompatible transparencies.

or

See Paper path troubleshooting, later in this chapter for more information. CAUTION: Use only transparencies specified for use with HP Color LaserJet printers.

Noncompatible transparencies can damage the printer. See the HP LaserJet Printer Family Print Media Specification Guide. 1. 2.

Remove all non-compatible transparencies from Tray 1. Load compatible transparencies in Tray 1.

20 insuffient memory

打印機接受太多的數據,超出了打印機的內存範圍

2.

20.10

Receive-fax directory is missing 接受传真的目录丢失

Paper stopped at the Face-down bin Check the paper path. This jam is sensed by PS1402 on the sensor PCA.

1. 按[GO]按鈕,繼續打印(部分打印內容可能丟失)； 增加打印機內存

20.20 Send-fax directory is missing 发送传真的目录丢失

20.30 Send-ID file is corrupted 发送 ID 的文件已损坏

20.40 Receive-ID file is corrupted 接收 ID的文件已损坏

第 7 页 共 43 页

20.50 Fax log is corrupted 传真日志已损坏

20.60 Flash init is required because of a firmware upgrade

因为固件升级，必须将闪存初始化

20.6060 Write to flash failed 写到闪存失败

21 page too comlex 21.00 page punt

打印的內容太複雜 1. 2.

按[GO]按鈕,繼續打印(部分打印內容可能丟失)；

將PAGE PROTECT值設置為AUTO

22 EIO X buffer overflow 送到指定的EIO外設的數據太多 按[GO]按鈕清除此信息（傳送的數據也將會丟失）

22 EMBEDDED I/O BUFFER OVERFLOW The embedded HP Jetdirect print server 嵌入（主板集成）的输入、输出缓冲区溢出

buffer has overflowed during a busy state. 在繁忙状态下，嵌入的（主板集成）的HP 打印服务器缓冲区溢出

1. Press √to continue printing.NOTE Data will be lost. 注意：数据将丢失

2. 3. 4.

Turn the printer off and then on.先关机再开机

Try printing the job again.尝试再打印这个作业

If the error persists, replace the formatter. 如果还报错，恢复到出厂设置

22 PARALLEL I/O BUFFER OVERFLOW Too much data was sent to the parallel port. 1. 并行的输入、输出缓冲器溢出

太多的数据发送到并口

2.

Press√ to continue printing.NOTE Data will be lost. 按√继续打印。注意:数据将丢失。

If the error persists, disconnect the parallel cable at both ends and then reconnect it. 如果还报错，将并口线的两头拆出，然后重新接上

3. Make sure that a high-quality parallel cable is being used.确认使用了好质量的并口线

4. With the parallel cable connected to the computer, connect the other end to another printer.将并口线的一头接电脑，另一头接另一台打印机来测试

5. 6.

Replace the parallel cable if necessary. 有需要的话，更换并口线 Replace the formatter if necessary. 恢复出厂设置

22 USB I/O BUFFER OVERFLOW USB 输入、输出缓冲器溢出

The printer USB buffer has overflowed during 1. a busy state.

Press √to continue printing.NOTE Data will be lost.按√来恢复打印。

第 8 页 共 43 页

在繁忙状态下，打印机的USB缓冲区溢出

2.

注意：数据会丢失。

If the error persists, disconnect the USB cable at both ends and then reconnect it.如果还报错，拔出USB线的两头，再重新接上 3.

Make sure t …… 此处隐藏：5966字，全部文档内容请下载后查看。喜欢就下载吧 ……