HP各种机型面板信息汇总(4)

Toner (Y/M/C/K) level sensor abnormality

1. The connectors in the toner level

sensor control line are not connected properly.Reseat the memory controller PCB connector J201 and the DC controller PCB connector J1025.

2. Faulty memory controller PCB.

Replace the memory controller PCB. 3. Faulty DC controller PCB. Replace

the DC controller PCB.

54.06 54.10 54.11 54.12 54.13 54.14

Color density sensor error

Color-plane registration sensor(s) error Yellow density out of range Magenta density out of range Cyan density out of range Black density out of range

54.30.XX

Perform a CALIBRATE NOW in the CONFIGURE DEVICE / PRINT QUALITY menu on the printer control panel. 54.31 - Media Sensor Abnormality/ Afteradjustment Value Out of Spec

1. Try to calibrate the media sensor

again.

2. Dirty media sensor. Clean the media

sensor.

3. The connectors in the media

detection signal line are not properly connected.Reseat the media sensor connector J601,relay connector J5026, and DC controller PCB connector J1008.

4. Defective media sensor. Replace

the media sensor.

5. Defective DC controller PCB.

Replace the DC controller PCB.

54.30.XX HP3700 only

Halftone calibration error. XX Description:

06 - magenta data out of range. 07 - yellow data out of range. 08 - black data out of range. 09 - cyan data out of range.

54.32 error The image density adjustment value,color misregistration adjustment value,and PWM in the EEPROM (NVRAM) of the formatter.

54.32 -

Electrical Adjustment

light intensity of the sensor must be

adjustment value (see note below) are stored When the media sensor is replaced, the

第 16 页 共 43 页

Whenever a formatter or laser/scanner unit is adjusted.

replaced, you must calibrate the printer to Follow the procedure below to adjust update the values.

replacement)

2. Color misregistration adjustment (on

formatter replacement)

3. PWM adjustment (on both formatter and

laser/scanner unit replacement) Note: The PWM adjustment value enables formatter determines the value based on the amount of laser light received from the printer engine.

the light intensity. 2. Open the front door.

3. While pressing down the engine test

print switch, turn the printer ON. 4. Close the front door.

5. Load paper into Tray 1 (use plain

white paper for test printing). period,press the engine test print switch and test print.

7. One sheet of paper will be fed into

the printer from Tray 1 and will be delivered to the face-down delivery tray. 54.33 -

1. Defective laser/scanner. Replace

the laser/scanner unit. 2. Defective DC controller PCB.

Replace the DC controller PCB.

54.2 55.1 59.16 59.192 59.4

59.99 Errors

The all-in-one has experienced an internal hardware error.

Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the all-in-one to initialize.

If a surge protector is being used, remove it.

Plug the all-in-one directly into the electrical outlet. Use the power switch to turn the all-inone on.

55.1 Error

DC controller error. The device has experienced an Turn off the power by using the power switch, internal hardware error.

wait at least 30 seconds, and then turn on the power and wait for the device to initialize.

If a surge protector is being used, remove it. Plug the device directly into the wall socket. Use the power switch to turn the device on.

Check the engine (DCC) firmware version. Update if needed. Replace the DCC if a firmware upgrade does not resolve the issue.

1. Image density adjustment (on formatter 1. Turn the printer OFF.

reproduction of an image in the best tone. The 6. As the printer goes into READY

55.XX.YY DC CONTROLLER ERROR A printer command error has occurred. XX Description:

第 17 页 共 43 页

55.01 and 55.02 Errors: Replace the DC controller.

01 Input device

02 DC controller memory 03 No engine response 04 Communication

55 PRINTER ERROR

內部通訊錯誤

A printer error has occurred. X Description 0 NO_RESET_REPORT 1 NO_ENGINE_RESPONSE 2 EXCESSIVE_GLITCHES 3 LOST_PPRDY_SIGNAL 4 COMMUNICATION_TIMEOUT 5 BAD_TRAY_BIN_REPORTS 6 ECC7_COMMAND_ERROR 7 INCOMING_PARITY_ERROR 8 OUTGOING_PARITY_ERROR 9 MISSED_INTERRUPT A HUNG_COMMUNICATIONS B LOST_XISR_ERROR C INVALID_BUS_TIMEOUT D VERY_LATE_ECOMM_ISR

56 * PRINTER ERROR

臨時打印錯誤，*值表示：

1. 不正確的輸入或錯誤的附加設備被連接 2. 不正確的輸出

57.xx PRINTER ERROR

55.03 and 55.04 Errors: 1. Check the DC controller

connectors.

2. Replace the DC controller. 1. 檢查電源位置 2. 更換接口板 3. 更換DC控制板

1. 重新啟動打印機； 2. 檢查打印機的配置； 3. 校正連接的附加設備

檢查打印機的風扇是否被正確的接入以及是否被阻礙物卡住； 2.

更換風扇

風扇錯誤(A printer fan error has occurred). 1. XX Description: 03 Sub fan 04 Main fan HP8150:

A fan motor failure occurred. All fans are enabled to low speed operation at power on. Fans will go into high speed operation during the print cycle. X Description

2 Fan 3 - Formatter Fan (intake)

3 Fan 2 - Low-voltage power supply (exhaust) 5 Fan 1 -Laser/scanner (exhaust) Low-voltage power supply (exhaust)

6 Fan 4 - Face-down delivery (exhaust) 9 Fan 5 - Tray 1 fan

58.XX ERROR A processor error has occurred. X Description

1 Tray 1 lifter malfunction. 2 Tray 2 lifter malfunction. 3 Tray 3 lifter malfunction.

第 18 页 共 43 页

Check the cable connection of the DC controller (J301) to the low-voltage power supply (J201).

…… 此处隐藏：6171字，全部文档内容请下载后查看。喜欢就下载吧 ……