HP各种机型面板信息汇总(3)

2. Make sure that all trays are configured and loaded correctly before printing again.

3. If the error persists, perform a paperpath test using the

diagnostics menu to make sure that all of the sensors are working correctly.

4. If the error persists, replace the paperfeed assembly.

41.X ERROR A printer error has occurred. 1. 2.

Press√ to continue or press ? For more information.

If the error persists after exiting help,turn the printer off and then on.

49.XXXXX ERROR A critical firmware error has occurred that 1. caused the processor on the formatter to abort operation. This type of error can be caused by invalid print commands, corrupt electrical noise in the cable can corrupt data during transmission to the printer. Other causes include poor-quality parallel cable, poor connections, or home-grown programs.

On rare occasions, the formatter is at fault which typically appears as a 79 Service Error. 翻译：

一个关键的固件错误造成处理格式时出现故障。这类错误可能是由于一些无效的打印命令、错误的数据、或者无效的驱动引起的。在某些情况下，电子干扰也会破坏在线缆中传输的数据。其他原因包括并行数据线、断续的网络连接或PC的应用程序。在个别情况下，格式发生故障时，有时也会报79服务错误代码 。

8. 9. 7. 6. 5. 3.

data, or invalid operations. In some cases, 4.

2.

Turn the printer off and then on. Press Stop to clear all print jobs from the printer memory.

Turn the printer off and then on. Try printing a job using a different software program. If the job prints, try using the original software program to print a different job.

NOTE If the error message only appears when using certain software programs, contact the software program vendor for assistance.

If the message persists with different software programs and print jobs, disconnect all of the cables and turn the printer off. If the error persists, perform a firmware upgrade.

Remove all DIMMs, EIO devices, and CompactFlash solutions. Remove all EIO devices. Turn the printer on.

reinstall the DIMMs, EIO devices, and CompactFlash one at a time. NOTE You must turn the printer off and then on when reinstalling each

10. If the error does not persist,

第 11 页 共 43 页

component.

11. Replace the DIMM, EIO device, or

CompactFlash if necessary. 12. Reconnect all of the cables.

49.3046

打印A3幅面的图片，超过2张时，显示该错误代码。内存不够，添加内存可以解决。 （HP5550）

50.* FUSER ERROR

加熱組件錯誤,其*值表示如下: 1 加熱溫度偏低 2 加熱組件預熱保護 3 加熱溫度偏高 4 電源電壓不穩 5 加熱組件不匹配

8 加熱溫度偏低 （低于最低限度） 9 加熱溫度偏高 （低于最低限度）

51.1Y

A laser beam error has occurred. Y Description: 0 Black

3. 4. 1. 2.

Turn the printer off and then on. Verify the laser/scanner assembly is connected correctly to the DC controller.

If the error persists, replace the laser/scanner assembly.

If the error persists, replace the DC controller.

51.XY. PRINTER ERROR

激光掃描錯誤 X Description: 1 -激光器檢測錯誤 2 -激光器錯誤 Y Description: 0 - no color K - black C - cyan M - magenta Y - yellow

51.20 Error 51.21 Error 51.22 Error 51.23 Error

1. 2. 3.

關掉電源,20分鐘后再開機; 重新安裝加熱組件;

關掉電源,取出加熱組件,檢查J1307-1和J1307-2以及J1308-1和J1308-2是否相通,如不通,更換另熱組件

1. 2. 3.

重新啟動;

重新安裝激光器及相連的電纜線; 更換激光器

The device has experienced an internal hardware error.

51.20 Error—black scanner error 51.21 Error—cyan scanner error 51.22 Error—magenta scanner error 51.23 Error—yellow scanner error

Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the device to initialize.

If a surge protector is being used, remove it. Plug the device directly into the wall socket. Use the power switch to turn the device on. Laser scanners are not replaceable. Replace the engine.

52.XX.Y A printer error has occurred. 1. Turn the printer off and then on.

第 12 页 共 43 页

X Description: 00 Scanner motor 01 Scanner startup 02 Scanner rotation Y Description: 0 Black

2. Verify the laser/scanner is connected correctly to the DC controller.

3. 4.

If the error persists, replace the laser scanner assembly.

If the error persists, replace the DC controller.

52.XY PRINTER ERROR

A laser/scanner motor failure has occurred 1. X Description: 1 - scanner error

2 - scanner startup error 3 - scanner rotation error Y Description: 0 - no color K - black C - cyan M - magenta Y - yellow

4. 5. 3. 2.

Press to continue.

If the message persists, turn the printer off and then back on. The connectors in the

laser/scanner control line are not connected properly. Reseat the DC controller PCB connectors (J1022, J1026, J1027) and the

laser/scanner connectors (J101A, J101B, J5001A, J5001B,J5020). Faulty laser/scanner, replace the laser/scanner.

Faulty DC controller PCB, replace the DC controller PCB.

52.* PRINTER ERROR 激光器掃描速度不匹配,*值表示如下: 1 掃描啟動錯誤 2 掃描旋轉錯誤

1. 2. 3. 1. 2. 3.

重新啟動;

重新安裝激光器及相連的電纜線; 更換激光器

Press √ to continue.

If the printer does not enter the Ready state, turn the printer off. Make sure that the installed memory meets requirements and is installed correctly.

53.10.01 ERROR UNSUPPORTED RAM The memory DIMM is not a supported DIMM.

4. Install a supported DIMM if necessary.

53.XY.ZZ CHECK DIMM A Bank B alternates with Press STOP to continue

HP 3700 only

An error occurred in printer memory. Values of A, and ZZ are: A Device Location:

1 - DIMM Slot 1 (bottom slot) 2 - DIMM Slot 2 3 - DIMM Slot 3 4 - DIMM Slot 4 ZZ …… 此处隐藏：6294字，全部文档内容请下载后查看。喜欢就下载吧 ……