M215HW01VC Open Cell规格书(2)

Item

Viewing Angle

Unit [degree]

Conditions

Horizontal (Right) CR = 10 (Left) Vertical (Up) CR = 10 (Down)

Contrast ratio

Normal Direction Raising Time (TrR)

Response Time

[msec]

Falling Time (TrF) Raising + Falling

Min. 40 40 15 40 360 - - -

Typ. 45 45 20 45 600 3.8 1.2 5

Max. - - - - - 5.5 2.5 8

4 Note

2

3

Color / Chromaticity Coordinates (CIE)

Red x Red y Green x Green y Blue x Blue y

0.618 0.309 0.252 0.573 0.113 0.04 0.283 0.299

160 75

0.648 0.339 0.282 0.603 0.143 0.07 0.313 0.329

200 80

0.678 0.369 0.312 0.633 0.173 0.1 0.343 0.359

- - 1.5 -20

6 7 8 9 5

Color Coordinates (CIE) White Central Luminance Luminance Uniformity Crosstalk (in 60Hz) Flicker

[cd/m] [%] [%] dB

2

White x White y

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

Note 1: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring (at surface 35℃). In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.

Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)

Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle.

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

Note 3: Contrast ratio is measured by TOPCON SR-3

Note 4: Definition of Response time measured by Westar TRD-100A

The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full White” (rising time, TrR), and from “Full White” to “Full Black” (falling time, TfF), respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of amplitudes.

TrR

FNote 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3 Note 6: Central luminance is measured by TOPCON SR-3

Note 7: Luminance uniformity of these 9 points is defined as below and measured by TOPCON SR-3

Note 8: Crosstalk is defined as below and measured by TOPCON SR-3

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

CT = | YB – YA | / YA × 100 (%) Where

YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2)

Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3

Gray Level = L0 Gray Level = L127

Method: Record dBV & DC value with TRD-100

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

3.0 Functional Block Diagram

The following diagram shows the functional block of the 21.5 inch Color TFT-LCD Module:

I/F PCB Interface:

FI-XB30SRL-HF11 (JAE)

or 093F30-B0T01A (Starcoon)

Mating Type:

FI-X30HL (Locked Type)

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

4.0 Absolute Maximum Ratings

Absolute maximum ratings of the module are as following:

4.1 TFT LCD Module

Item Logic/LCD Drive

Voltage

Symbol VDD

Min 4.5

Max 5.5

Unit [Volt]

Conditions Note 1,2

4.2 Backlight Unit

Item CCFL Current

Symbol ICFL

Min 3.0

Max 8.5

Unit [mA] rms

Conditions Note 1,2

4.3 Absolute Ratings of Environment

Item

Operating Temperature Operation Humidity Storage Temperature Storage Humidity

Symbol

TOP HOP TST HST

Min.

0 5 -20 5

Max.

+50 90 +60 90

Unit

[C] [%RH] [C] [%RH]

oo

Conditions

Note 3

Note 1: With in Ta (25℃)

Note 2: Permanent damage to the device may occur if exceeding maximum values

Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard).

Operating Range Storage Range

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification

Input power specifications are as following:

Symbol VDD IDD

Parameter Logic/LCD Drive

Voltage Input Current

Min 4.5 -

Typ 5.0 0.98

Max 5.5 1.22

Unit [Volt] [A]

+/-10%

VDD= 5.0V, All Black Pattern At 60Hz,

4.9 -

6.1 3

[Watt] [A]

VDD= 5.0V, All Black Pattern At 60Hz Note 1

VDD= 5.0V, All Black Pattern At 75Hz

Conditions

PDD IRush

VDD Power Inrush Current Allowable Logic/LCD Drive Ripple Voltage

- -

VDDrp

-

- 300 [mV] p-p

Note 1: Measurement conditions:

The duration of rising time of power input is 470us.

Product Specification

AU OPTRONICS CORPORATION

M215HW01 VC

5.1.2 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when VDD is off. Please refer to specifications of SN75LVDS82DGG (Texas Instruments) in detail.

1. DC Characteristics of each signal are as following:

Symbol VTH VTL │VID│

Parameter

Differential Input High Threshold

Differential Input Low Threshold

In …… 此处隐藏：4686字，全部文档内容请下载后查看。喜欢就下载吧 ……