台达标准10000-016216-ENG(2)

2

SCOPEThis Technical Standard applies to the following parts/ devices constituting Delta products: Electrical parts, mechanical parts, semiconductor devices, printed wiring boards (PWBs), and packaging materials/ packaging parts. Including assemblies such as functional units, modules, and board assemblies. Including attachments such as the accessories procured as parts. Including composing materials such as the subsidiary parts and materials managed by parts specifications. Including the s

ubstances used in the production processes of parts. Including repair parts. Regarding the substances or their purposes whose use is banned by regional or country laws and ordinances or customers, the laws and ordinances or standard of customers must be observed even though the substances or their purposes are not clearly regulated in this technical specification.

DELTA ELECTRONICS, INC.THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.

DESCRIPTION: MANAGEMENT STANDARDS FOR ENVIRONMENT-RELATED SUBSTANCES DRAWING NO.: REV.

10000-0162SHEET2

16TO49

台达标准

3

OPERATIONAL PROCEDUREDeliberations and decisions on matters regarding this Standard shall be made by the“Technical Committee for Environment-related Substances” The matters thus deliberated and decided shall be approved by the head of the division promoting the company-wide standardization of technology. When this Standard requires revising or abolishing, apply to the Technical Committee for Environment-related Substances for the revisions or abolishment. The Committee shall deliberate the applied contents and decide the revisions or abolishment.

4

DEFINITIONS OF TERMSIn this Standard, terms are defined as follows: Environment-related substances: Among the substances included in the parts and devices (refer to the SCOPE) or the ones used at the time of manufacture, environment-related substances are the ones that are said to have serious environmental effects on overall global environment and that are specified by Delta. Management standards: To manage the above-mentioned substances, the following three levels are used. 1. Level 1 The substances and purposes classified at this level are those whose use must be banned immediately. Level 2 The substances and purposes classified at this level are those for which periods for phase-out are individually set. After the time set in each table, the substance fulfilling the above condition will be classified at Level 1 and must not be contained in parts and materials. Level 3 No periods or targets for reduction are currently set for the substances and purposes classified at this level. However, the contents of the substances in parts and materials ought to be reduced. (need to report) Exemption The substances classified into this level are those not regulated by the law or excluded from the“controlled substance” due to insufficient supply of adequate alternative parts and materials that satisfy the intended application.

2.

3.

4.

DELTA ELECTRONICS, INC.THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.

DESCRIPTION: MANAGEMENT STANDARDS FOR ENVIRONMENT-RELATED SUBSTANCES DRAWING NO.: REV.

10000-0162SHEET3

16TO49

台达标准

Homogeneous mat

erials: Homogeneous materials are defined as materials that cannot be mechanically disjointed into different materials and are“of uniform composition throughout”. Banned substances: Among the substances included in the parts and devices (refer to the SCOPE) or the ones used at the time of manufacturing, banned substances are those hazardous substances that are not allowed to be added intentionally and to be contaminated accidentally. The threshold limits of those banned substances are specified in any applicable test methods that are regulated in any related regulations and laws. The time to ban on receiving the parts and materials: This indicates the time when Delta must not receive the parts and/or materials specified in this specification. TBD: To be defined. N.D: Not detected/ not detectable. N/A: Not available. PPM, ppm: Parts per million, unit of measurement for weight percentage. 1 ppm=1 mg/kg=0.0001% by weight. Packaging: Materials used to protect products from damage due to storage or transportation (e.g., boxes, shipping supplies, cushioning& foam, bags, shrink wrap, tape/adhesives). Includes inks and dyes used to label packages. Reusable or returnable packaging under the control of traders or suppliers is out of this scope. EPA: Environmental Protection Agency. FT-IR: Fourier Transform Infrared Microscopy. GC/MS: Gas Chromatography/ Mass Spectrometry. HPLC/UV: High Performance Liquid Chromatography/ Ultra Violet Light Spectrometry. CAS: Chemical Abstract Service. IEC: International Electrotechnical Commission. Mechanical plastic part: DESCRIPTION: MANAGEMENT STANDARDS FOR ENVIRONMENT-RELATED SUBSTANCES DRAWING NO.: REV.

DELTA ELECTRONICS, INC.THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA ELECTRONICS, INC. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION.

10000-0162SHEET4

16TO49

台达标准

Plastic parts that do not internally carry an electrical signal such as housings, brackets, bezels, latches, etc that form the basic structure of the product and/or have mechanical functions.

5

REFERENCESIPC/EIA J-STD 006A (May 2001) for Electronic Grade Solder Alloys. Directive of the European Parliament and of the Council on Marketing and Use of Dangerous Substances, 76/769/EEC, July 1976. Council Dire …… 此处隐藏：5993字，全部文档内容请下载后查看。喜欢就下载吧 ……