最全模具英语日语(超级实用)

很实用很全面

模具常用英语！

2008年09月12日 星期五 15:56

模具英语句子

1． XXX！你现在有空吗，我可以问你一些问题吗？

Could I ask you some questions if you are free? / Are you fr

2． 请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？

Can you tell me whether the surface of this part is a visibl

surface? Texture or Polishing ?

3． 请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？

Does this part need an ejector pin or an ejector bar? Can we

4． 这个产品的柱位我们打算做司筒。（或镶针）可以吗？

Can we add ejector sleeves or ejector pins in the boss of th

5． 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线

There's an undercut at this position and it needs a slider.

this side, is that OK?

6． 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？

We will make the lifter and (inner) slider in this position,

7． 你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？

The 2D and 3D drawing you provided is not the same, can you

8． 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的

There is no draft angle in the 3D drawing, some materials ar

thin. Can we modify this part by ourselves? We will sen

9． 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了

According to the shrinkage one over two hundred, the mold ha

10． 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗

This position is too small and will make the steel material

11． 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移

The angular lifter interferes with the boss during ejection.

12． 这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位

The rib here is too thin and on the high side, so it will be

injection, can you increase the thickness of this rib?

13． 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公

Will you increase/decrease the material on this rib? We will

很实用很全面

14． 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在

This sample has been burned in the bottom because the ventin

15． 重做镶件大约需要5-6天时间，你能接受吗？

It will take about 5 or 6 days to redo the insert, is that O

16． 产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我

We have made the texture on this side, if we add material, i

texture by out-resourcing, so we suggest using the texture b

17． 模具是用公制/英制的配件？需要备用件吗？

Is this mold dimension measured in inches or meters? Does it

18． 模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这

Will you provide the engraving content of the plate of this

19． 可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大

Can you provide the type of injection machine and other rela

Such as the boss dimension, the hole's dimension of the ejec

machine and so on.

20． 这个问题我需要同其它同事商议会再答复你。

I need to discuss this problem with the other colleagues and

21． 我们将尽力达成你的计划，如有异常，会及时通知你。

We will try our best to complete your plan, if there are any

immediately.

22.这个产品的长度为330.12MM,宽度为78.96MM,高度为45MM.胶厚为2M

The length of this part is 330.12MM, Width is 78.96MM, heigh

23． 现在到了吃午钣的时间，我们下午再继续好吗？

It is time to have lunch, let's discuss this project later t

24.和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動

(The undercut area interferes with the slide block and needs

25. 加肉太多 (The thickness added is too thick.)

26. 加肉面積太大 (The thickening area is too wide.)

27.GATE位置移位 ( The gate position is moved.)

28. 滑塊拆的位置 (The split line of slide block or the

29. 此處有尖角，填充困難 (It is hard to fill this area due to

30. 此處鋼材太薄，強度不足而且不容易冷卻

(The strength of this area is too weak and it is hard to coo

31. 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉

(We avoid designing the semicircle of the cylinder on the sl

很实用很全面

apart or cause drag marks.)

32. 此處做斜銷在作動時會削到成品肉厚

(The part will be damaged if we make the lifter in this area

33. 這個面是裝配面，不能加料

(This is a critical surface where we cannot add additional m

34. 此處料位太厚，會有縮水，建議減料改善

(Because of the shrinkage of the thickness, we suggest reduc

35. 此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受

(Please confirm whether it is a critical surface or not. Als

36. 此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷

(Please confirm whether we can reduce material to the area w

37. 請盡快確認這種拆模方式和結構，否則會影響模期

(Please confirm the issues of Parting line, Gate position...

the lead-time will be extended.)

38. 此面是否有特殊要求，能否有頂針印

(Please confirm whether it is a critical surface or not and

39. P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響

(There are sharp edges if we set the parting line here, It w

40. 加大拔模角，以便脫模順利 We suggest enlarging the draft

41. GATE做在此處的話有兩個缺點：1.蓋子打開時可以看到GATE的修剪

(There are two problems if the gate is to be designed in thi

a). It is easy to see the gate mark when you open the c

b). The ejectors are unbalanced when two lifters are on

42. GATE做在此處的話.蓋子打開後看不到GATE的修剪部位

(The gate mark is not visible if the gate position is design

43. 如果GATE一定要做在你們指定的位置的話，那還不如做在這一側，

(If you insist that the gate position has to be like th

design, then we would further 44. 在此處GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又

(If the design of the gate has to be a sub. Gate, then the b

serious flow marks due to the black color.)< …… 此处隐藏：18082字，全部文档内容请下载后查看。喜欢就下载吧 ……