2557-X02 DK跌落测试报告(package drop test report)

SAM'S 53 #2557-X02(DK)包装跌落测试报告产品名称 product name 材质 material NO. SAM'S 53 / 型号/规格 type /spec. 测试日期 test date 2557-X02 2011-11-5

测试要求及条件(依 test requirement and

1、测试方法： 依如下高度要求，对产品进行6次跌落测试，测试完成后产品不可有明显损坏，破 test method According to the following height requirements, the product 6 drop test phenomena; ( surface, angle, edge selection see below picture logo). 编号 No. 1 2 1 3 4 5 6 跌落高度 drop height 8 in (20.3cm) 8 in (20.3cm) 8 in (20.3cm) 8 in (20.3cm) 8 in (20.3cm) 14 in (35.6cm) 跌落部位 drop position 面1 face 1 面2 face 2 面6 face 6 角 2-3-5,,任意选一项 conner 2-3-5,Arbitrarily select an item 边3-4,任意选一项 edge 3-4 arbitrarily select an item 面6 face 6

测试过程 testing pr 测试过程(附图)testing process(figure)

测试面1 test face1 (8in/20.3cm)

测试过程(附图)testing process(figure)

测试面2 test face 2 (8in/20.3cm)

test requirement and

drop position 1face 1 2face 2 6face 6 2-3-5,，任意选一项3-4，任意选一项6

face 6test face 2

（8in/20.3cm）

测试面2 test face 2 (8in/20.3cm)

测试过程(附图)testing process(figure)

测试点3:面6 (8in/20.3cm)

测试过程(附图)testing process(figure)

测试角4:角 2-3-5,,任意选 一项(8in/20.3cm) test conner 4: conner 2-3-5 Arbitrarily select an item

测试过程(附图)testing process(figure)

测试点5:边3-4,任意选一项 (8in/20.3cm) test point Arbitrarily select an item

测试过程(附图)testing process(figure)

测试点6:面6 (14in/35.6cm) test point 6:face 6

跌落测试图片如下(follow drop test figure):

跌落之后图片( after drop tested figure)

跌落测试图片如下（follow drop test figure):

跌落之后图片（ after drop tested figure)

M'S 53 #2557-X02(DK)包装跌落测试报告(package drop test report)2557-X02 2011-11-5 送检单位 Submission unit 送样数量 sample quantity 测试要求及条件(依据BV测试方法) test requirement and condition(according

品进行6次跌落测试，测试完成后产品不可有明显损坏，破裂等不良现象；(面、角、边选择参见下图标识) lowing height requirements, the product 6 drop test, after testing products have no obvious damage, such as r , angle, edge selection see below picture logo). 跌落部位 drop position 面1 face 1 面2 face 2 面6 face 6 角 2-3-5,,任意选一项 conner 2-3-5,Arbitrarily select an item 边3-4,任意选一项 edge 3-4 arbitrarily select an item 面6 face 6 测试过程 testing process 测试结果(附图)test reuslt (figure) 没有破损 No damage

过程(附图)testing process(figure)

过程(附图)testing process(figure)

测试结果(附图)test reuslt (figure)

3 #2557-X02(DK)包装跌落测试报告（package drop test report)测试要求及条件（依据BV测试方法）test requirement and condition(according

次跌落测试，测试完成后产品不可有明显损坏，破裂等不良现象；（面、角、边选

lowing height requirements, the product 6 drop test, after testing products have no obvious damage, such as r, angle, edge selection see below picture logo).

测试过程 testing process

est reuslt (figure)

没有破损 No damage

过程(附图)testing process(figure)

测试结果(附图)test reuslt (figure) 没有破损 no damage

过程(附图)testing process(figure)

测试过程(附图)test reuslt (figure) 没有破损 No damage

过程(附图)testing process(figure)

测试过程(附

图)test reuslt (figure) 没有破损 No damage

过程(附图)testing process(figure)

测试过程(附图)test reuslt (figure)

PDQ搭桥边角处轻微变形。有一套吸塑壳轻微破损,测试结果比BV 破损面积小，QAAC判定合格。 PDQ bypass corner of slight deformation. There is a set of plastic shell slightly damaged, test results than BV damage area is small, QAAC considered qualified.

tested figure)

tested figure)

drop test report)C Y houseware http://doc.guandang.net 1箱(case)

ing

面、角、边选择参见下图标识) products have no obvious damage, such as rupture of undesirable

结果(附图)test reuslt (figure) 没有破损 No damage

判定 judge

OK

结果(附图)test reuslt (figure)

判定 judge

ing

没有破损 No damage

ok

结果(附图)test reuslt (figure) 没有破损 no damage

判定 judge

OK

过程(附图)test reuslt (figure) 没有破损 No damage

判定

OK

过程(附图)test reuslt (figure) 没有破损 No damage

判定 judge

OK

过程(附图)test reuslt (figure)

判定 judge

微变形。有一套吸塑壳轻微破损,测试结果比BV 破损面积小，QAAC判定合格。 er of slight deformation. There is a set l slightly damaged, test results than BV is small, QAAC considered qualified.

OK