FHSW-5使用说明书(3)

the device seawater entering pipe line flange joint the force lift pump entrance. ⑶ 将排放管路与装置排放口法兰连接。 the drain pipeline joint the device drain flange.

⑷ 将不合格水排放管路与装置不合格水排放口法兰连接。

the device substandard water pipeline flange joint the substandard water flange of the device ⑸ 将淡水管路与装置淡水出口连接。

the fresh water pipe line joint the fresh water exit of the device.

⑹ 将装置电源进线及外接控制线接入装置电控箱内接线端子。端子位置见附5（电气接线图）。 wire the mains entering lead of the device and the outer control lead to wiring terminal of the device electric control cabinet, terminal position see attached 6 (electric wiring drawing).

装置安装完毕。

2、启动前准备get ready before start

a、检查机械过滤器状态。Check the state of mechanical filters

检查机械过滤器的手动多路阀手柄处于“运行”状态。

Multi-port Valve of. mechanical filters is service

b、打开V1、V2、全开面板上浓水调节阀V8

wholly open V1、V2 and open the dense water adjusting valve V8 on the face plate,

c、将三通阀V3打到高压泵进水与保安滤器连通位置；将三通阀V4打到浓塑海水直接排放位置；

将三通阀V5打到产淡水和清洗水箱连通位置

make the three-way valve V3 on the position of the high pressurepump inlet and fine filter, make the three-way valve V4 on the position of serwater release to outboard; make the three-way valve V5 on the position of freshwater and cleaning box.

d、设定压力控制器。将高压泵供水欠压压力控制表PS1设定在0.1Mpa位置，反渗透膜进水超压

压力控制器PS2设定在6.5Mpa，反渗透膜产水超压压力控制器PS3设定在0.2Mpa。装置在出厂前已经设定好，可进行检查核对。

set up the pressure controller. Set the high pressure pump water supply owes pressure controller PS1 on the position of 0.1MPa, reverse osmosis membrane enter water exceed pressuer controller PS2 on the position of 6.5MPa, reverse osmosis membrane production water exceed pressuer controller PS3 on the position of 0.2MPa. The device has set before leaving factory, may carry on check.

e、合上电控箱内空气开关；close the air switch in the electric control cabinet.

f、将电控箱上“冲洗/清洗/工作”拨至“工作”位置

Changzhou Feihua Marine Machinery Co., Ltd. 10 Tel：0519-88602365 Fax：0519-88609065

Electronic control box will be the \g、接通电控箱电源，将电控箱上“电源开/关”达到“开”位置，可以看到电源指示灯亮。 put through the mains in the electric control cabinet, make the “mains off/on ” on the “on” position, may see the mains indication lamplight.

3、 启动start

a、按下“启动按钮”，低压泵开始运转，10秒后高压泵延时启动；

Push the launch button “START”,low pressure pump start and work, after 10 s, high pressurepump start b、待装置面板上浓水流量计指示稳定后，缓慢调节面板上反渗透浓水调节阀V8，这时反渗透膜进水压力开始上升并开始产水，观察反渗透膜进水压力表及产水流量计，至反渗透产水流量计达到 9.2GPM，这时反渗透膜进水压力应在4.0～6.5Mpa之间；

Panels to be installed on the instructions of the stability of concentrated water flow meter, the slow adjustment panel concentrated reverse osmosis water regulating valve V8, then reverse osmosis membrane water pressure began to rise and begin production of water, observe the pressure gauge and water reverse osmosis membrane production of water flow meter, flowmeter to reverse osmosis water production reached 69.5 LPM, then reverse osmosis membrane water pressure should be between 4.0 ~ 6.8Mpa;

e、检查盐量计指示值是否 ≤ 700mg/L。

Salt content of the instructions to check whether the value of ≤ 700mg / L

装置运行调节完毕,可以投入正常运行状态。正常运行状态中，装置浓水调节阀不需调整。 End of run-conditioning devices. Can be put into operation automatically. Automatic operation, the concentration of water regulating valve device needs no adjustment。

4、 停机device stop

a、缓慢打开浓水调节阀V8至全部打开；

slowly open dense water adjusting valve V8, till whole open;

b、按下电控箱上“停止”按钮，对应的工作指示灯灭，低压泵、高压泵停止工作； Push the launch button “STOP” on electric control cabinet, the corresponding indicator light work out, low pressure pump、high pressure pump shutdown;

c、切断电源。cut out the mains. D、装置停机。The device stop.

5、 装置自动运行the device automatically running

装置按手动运行操作启动后，即可投入运行。

By manually operated devices to start running, you can put into operation 装置自动运行过程中，将有以下情况：

Changzhou Feihua Marine Machinery Co., Ltd. 11 Tel：0519-88602365 Fax：0519-88609065

During the device automatically running, there are following conditions:

⑴ 当装置进水压力过低时，低于0.1MPa时，系统停机并发出报警。此时需切断装置电源，使装置控制复位。再重新启动装置。

⑵ 当反渗透膜进水压力过高时，高于6.5MPa时，系统停机并发出报警。此时需切断装置电源，使装置控制复位。再重新启动装置。

⑶当反渗透膜产水压力过高时，高于0.2MPa时，系统停机并发出报警。此时需切断装置电源，使装置控制复位。再重新启动装置。

⑷当多介质过滤器进入反冲维护状态时，高压泵将停止工作，待多路阀完成反冲，回到正常工作状态后再自动投入运行。

1）When device water entering pressure is too low, lower than 0.1MPa, device stops and alarms with sound and light. Now must cut off device mains, let device control reset. Then start force lift pump, start device.

2）When reverse osmosis membrane water entering pressure is too high, higher than 6.5MPa,device stops and alarms with sound and light. Now must cut off device mains, let device control reset. Then start force lift pump, start device.

When reverse osmosis membrane production water pressure is too high, higher than 0.2MPa,

device stops and alarms with sound and light. Now must cut off device mains, let device control reset. …… 此处隐藏：7472字，全部文档内容请下载后查看。喜欢就下载吧 ……