网关及变频器设置

Training \ TASC \ Driving Control Products 1

SEW 驱动控制产品

Driving the world

Training \ TASC \ Driving Control Products 2

SEW 驱动控制产品

UFP11A网关介绍设备状态灯RUN 总线状态灯BUS-F 系统状态灯SYS-F 专家模式灯USER SBUS接口 拨码开关 RS485调试接口 PROFIBUS接口

Driving the world

Training \ TASC \ Driving Control Products

SEW 驱动控制产品

硬件组态UFP1:GND 2:SC11 3:SC12 4:24V 5:GND

MC07BGND SC11 SC12 24V GND 终 端 on 电 off 阻 SC21 SC22 GND

MC07B终 端 on 电 off 阻SC11 SC12 GND

1、此例由变频器给网关供24V 2、末端变频器的终端电阻要打开 3 、MC07B的系统总线模块在FSC11B上面Driving the world

Training \ TASC \ Driving Control Products 4

SEW 驱动控制产品

FSC模块

终端电阻拨码开关

系统总线

RJ10调试口

RS-485Driving the world

Training \ TASC \ Driving Control Products 5

SEW 驱动控制产品

Driving the world

Training \ TASC \ Driving Control Products 6

SEW 驱动控制产品

变频器参数设定 P100:SBUS、P101:SBUS P881(SBUS ADDRESS)、P882(SBUS GROUP ADDRESS)、 P883(SBUS TIMEOUT DELAY)、P884(SBUS BAUD RATE) 当上述设定不正确时，网关系统状态灯SYS-F会显示红灯 P601、P602、P603、P604都设定为NO FUNCTION,故不必 连接相应端子。由于P600(DI01)不可修改，故将DI01端子接 24V。 通过P870、P871、P872组态PO DATA;P873、P874、P875 组态PI DATA;P876设定为ON,使能PO DATA。 具体操作方式见调试步骤：

Driving the world

Training \ TASC \ Driving Control Products 7

SEW 驱动控制产品

按照要求连接计算机、网关和变频器，确认无误后上电 打开motion-studio软件，新建一个工程

Driving the world

Training \ TASC \ Driving Control Products 8

SEW 驱动控制产品

确认命名和存放位置以后，出现下列对话框，选取通讯串口

Driving the world

Training \ TASC \ Driving Control Products 9

SEW 驱动控制产品

进入主界面以后，点击SCAN后扫描到现有设备

SCAN

Driving the world

Training \ TASC \ Driving Control Products 10

SEW 驱动控制产品

点击右键出现如图菜单，进入parameter tree出现参数组,根据要 求修改相应参数

Driving the world

Training \ TASC \ Driving Control Products 11

SEW 驱动控制产品

点击UFP模块进行配置,点击右键,选择Configuration

Driving the world

Training \ TASC \ Driving Control Products 12

SEW 驱动控制产品

进入配置模式,可以进行网关和变频器之间的组态

Driving the world

Training \ TASC \ Driving Control Products 13

SEW 驱动控制产品

创建一个新的总线组态(选择文件生成路径)

Driving the world

Training \ TASC \ Driving Control Products 14

SEW 驱动控制产品

新建一个配置项目后,点击Update,进行设备搜索

Driving the world

Training \ TASC \ Driving Control Products 15

SEW 驱动控

制产品

通过CHANGE或双击图表按钮修改所选设备参数

Driving the world

Training \ TASC \ Driving Control Products 16

SEW 驱动控制产品

可以组态多台MC07B(最多8台)

Driving the world