PID控制步进电机转速仿真及c程序

PID控制步进电机转速仿真及c程序

#include #include\

sfr T2MOD = 0x0c9;

#define uchar unsigned char #define uint unsigned int

sbit Q0 = P2^4; sbit Q1 = P2^5; sbit Q2 = P2^6; sbit Q3 = P2^7;

sbit PWM = P1^7; sbit UP = P1^0; sbit DOWM = P1^1; sbit GORB = P2^3; //换相 sbit ADDSPEED = P1^2; sbit SUBSPEED = P1^3;

uinttuint = 65535;

uinttpwm = 1; //pwm周期为10000us tpwm变量表示pwm高电平时间，也相当于占空比 (仿真时，频率高时，电机反应慢。在实物上要加大频率) uchar t1_flag = 0;

uint pulse = 0; uint t0_flag = 0; uchar t2_flag = 0; bit t2_over = 0; bitJust_Get = 1;

#define ZZ { Q0 = 0;Q1 = 0;Q2 = 1;Q3 = 1;} //正转 #define FZ { Q0 = 1;Q1 = 1;Q2 = 0;Q3 = 0;} //反转 #define STOP { Q0 = 1;Q1 = 0;Q2 = 1;Q3 = 0;} //停止 //禁止出现 Q0 = 0;Q1 = 1;Q2 = 0;Q3 = 1; 不然会烧掉mos管

//************************ PID ************************************* float now = 0,bef = 0,bbef = 0; //本次采样值，上次采样值，上上次采样值 float err_now,err_bef,err_bbef; //当前偏差，上次偏差，上上次偏差 float error_add = 0; //所有偏差之和 float set = 25; //设定值

floatkp = 25; floatki = 25; floatkd = 0;

//*****************************************************************

void delayms(uintms)//延时？个ms {

uchara,b,c; while(ms--) { for(c=1;c>0;c--) for(b=142;b>0;b--) for(a=2;a>0;a--); } }

voidtimer_init() { EA = 1; ET0 = 1; ET1 = 1; ET2 = 1; TMOD = 0x15; //定时器0 计数模式定时器1模式1

T2MOD = 0x01; TH0 = TL0 = 255; TH2 = 0x3C; TL2 = 0xB0; //50MS }

void timer1() interrupt 3 { if(t1_flag == 0) { t1_flag = 1; PWM = 1; TH1 = (tuint - tpwm + 1)/256; TL1 = (tuint - tpwm + 1)%6; } else { t1_flag = 0; PWM = 0; TH1 = (tuint - 10000 + tpwm + 1)/256; TL1 = (tuint - 10000 + tpwm + 1)%6; } }

void timer0() interrupt 1 { TH0 = TL0 = 255; t0_flag++; }

void timer2() interrupt 5 { TF2 = 0; TH2 = 0x3C; TL2 = 0xB0; //50MS t2_flag++; if(t2_flag == 2) { TR0 = 0; TR2 = 0; t2_flag = 0;

t2_over = 1; //表示100ms时间到 } }

voidGetPulse() { t0_flag = 0; t2_flag = 0; TH0 = TL0 = 255; TH2 = 0x3C; TL2 = 0xB0; //50MS TR0 = 1; TR2 = 1; }

int PID() //增量式PID { int change; err_now = set - now; err_bef = set - bef; err_bbef = set - bbef; change = kp*(err_now - err_bef) + ki*err_now + kd*(err_now - 2*err_bef + err_bbef); /* if(set >= now) { if(set - now > 1) change = kp*(err_now - err_bef) + ki*err_now + kd*(err_now - 2*err_bef + err_bbef); else change = 0.2*kp*(err_now - err_bef) + 0.5*ki*err_now + kd*(err_now - 2*err_bef + err_bbef); } else if(now > set) { if(now - set > 1) change = kp*(err_now - err_bef) + ki*err_now + kd*(err_now - 2*err_bef + err_bbef); else change = 0.2*kp*(err_now - err_bef) + 0.5*ki*err_now + kd*(err_now - 2*err_bef + err_bbef);

*/ }

}

//change = (kp + ki + kd)*(set - now) + (-kp - 2*kd)*(set - bef) + kd*(set - bbef); //change = kp*(set - now) + ki*(set - bef) + kd*(set - bbef); if(change > 0) { printchar(1,10,'+'); printuint(1,11,4,change); }

else if(change < 0) { printchar(1,10,'-'); printuint(1,11,4,-change); }

else if(change == 0) { printchar(1,10,' '); printword(1,11,\ \}

return(change);

int PID2() //位置式PID { intnum = 0; staticnum_bef = 0; err_now = set - now; err_bef = set - bef; error_add = error_add + err_now; //误差累加。一旦误差为0则error_add的值不变，PID输出值不变 num = kp*err_now + ki*error_add + kd*(err_now - err_bef); /* if(set - now >= 0) {