《单片机原理及应用(C51)》(4)

void delay(unsigned char k) { unsigned char i,j; for(i=0;i<255;i++) for(j=0;j

2：如下图，编程实现开关控制 LED

说明：开关 S1 和 S2 分别控制 LED1 和 LED2 #include sbit S1=P1^0; sbit S2=P1^1; sbit LED1=P0^0; sbit LED2=P0^1; void main() { while(1)

{ LED1=S1; LED2=S2; } }

3：如下图，编程实现8个发光二极管先按状态1的形式点亮，经过一段时间延时，再按状态2的形式点亮，点亮形式见下表 P1.7 P1.6 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 P1口引脚 灭 亮 灭 亮 灭 亮 灭 亮 对应灯的状态1 对应灯的状态2 亮 灭 #include void delay( unsigned int time) { unsigned int j = 0; for(; time>0;time--) for( j=0;j<125;j++); }

void main( ) { while(1)

{ P1=0xaa; delay(500); P1=0x55; delay(500); } }

亮 灭 亮 灭 亮 灭 C130pFX1CRYSTALU1C2D1LED-REDD29LED-REDD3RST30pF18XTAL219XTAL1P0.0/AD0P0.1/AD1P0.2/AD2P0.3/AD3P0.4/AD4P0.5/AD5P0.6/AD6P0.7/AD7P2.0/A8P2.1/A9P2.2/A10P2.3/A11P2.4/A12P2.5/A13P2.6/A14P2.7/A15P3.0/RXDP3.1/TXDP3.2/INT0P3.3/INT1P3.4/T0P3.5/T1P3.6/WRP3.7/RD393837363534333221222324252627281011121314151617R10C310k293031PSENALEEALED-REDD422uFLED-REDD5U2:A18161412Y0Y1Y2Y3A0A1A2A3OE2468112345678P1.0P1.1P1.2P1.3P1.4P1.5P1.6P1.7AT89C51A0A1A2A3OE1113151719LED-REDD6LED-REDD7975374LS240U2:BY0Y1Y2Y3LED-REDD8LED-REDR81kR71kR61kR51kR41kR31kR21kR11k74LS24016

4：如下图，编程实现LED循环显示字符：“H” →“L” →“E”。 #include

char led_ mod[]={0x76,0x38,0x79}; //LED显示字模 void delay( unsigned int time) { unsigned int j = 0; for(; time>0;time--) for( j=0;j<200;j++); }

void main(void) { char i=0; while(1)

{for(i=0;i<=2;i++) { P0=led_mod[i]; delay(500); } }}

5、开机时LED全熄，然后根据按键动作使相应灯亮，并将亮灯保持到按压其它键时为止。 #include

R5R6R7R8void main() {

U1 char key = 0; P2=0; while(1){

key = ~P0 & 0x0f; //读取按键状态 R1D1 if (key != 0) P2 = key; //显示到led R2D2 }

R3D3}

R4D4

6、在P0口连接一个共阴极数码管，使之循环显示0～9数字。 #include //包括一个51标准内核的头文件 char led_mod[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; //LED显示字模 void delay(unsigned int time) { unsigned int j = 0; C2C130PFX130PFU1 for(;time>0;time--) 1939XTAL1P0.0/AD038P0.1/AD137 for(j=0;j<125;j++); P0.2/AD2CRYSTAL1836XTAL2P0.3/AD335P0.4/AD434} P0.5/AD5C333P0.6/AD6932RSTP0.7/AD7void main(void) { 2110uFR1P2.0/A822P2.1/A923 char i = 0; 10kP2.2/A102924R3PSENP2.3/A113025ALEP2.4/A123126 while(1){ R4220EAP2.5/A1327P2.6/A1428R5220.P2.7/A15 for(i=0;i<=9;i++) { 110R6220P1.0P3.0/RXD211P1.1P3.1/TXD312 P0=led_mod[i]; R7220P1.2P3.2/INT0413P1.3P3.3/INT1514R8220P1.4P3.4/T0615 delay(500); P1.5P3.5/T1716R9220P1.6P3.6/WR817P1.7P3.7/RD} } } 220AT89C511k1k1k1k+5V19XTAL118XTAL29RSTP0.0/AD0P0.1/AD1P0.2/AD2P0.3/AD3P0.4/AD4P0.5/AD5P0.6/AD6P0.7/AD7P2.0/A8P2.1/A9P2.2/A10P2.3/A11P2.4/A12P2.5/A13P2.6/A14P2.7/A15393837363534333221222324252627281011121314151617293031PSENALEEALED-YELLOW10012345678LED-YELLOW100P1.0P1.1P1.2P1.3P1.4P1.5P1.6P1.7P3.0/RXDP3.1/TXDP3.2/INT0P3.3/INT1P3.4/T0P3.5/T1P3.6/WRP3.7/RDLED-YELLOW100LED-YELLOW10080C51 17

7、设计一个开关控制报警器：用K1开关控制报警器，程序控制P1.0输出两种不同频率的声音，模拟很逼真的报警效果.

C2C1#include

22uF193930pF#define uchar unsigned char XTAL1P0.0/AD038X1P0.1/AD137CRYSTALP0.2/AD2C31836sbit SPK=P1^0; XTAL2P0.3/AD335R1P0.4/AD4341kP0.5/AD53330pFsbit K1=P1^7; P0.6/AD6932RSTP0.7/AD721void Alarm(uchar t) //发声函数 P2.0/A822P2.1/A923P2.2/A10U12924{ uchar i,j; PSENP2.3/A113025ALEP2.4/A12312680C51EAP2.5/A1327 for(i=0;i<200;i++) //循环次数控制音频的持续时间 P2.6/A1428P2.7/A15LS1110 { SPK=~SPK; P1.0P3.0/RXD211P1.1P3.1/TXD312P1.2P3.2/INT0413 for(j=0;j

void main() { SPK=0; while(1)

{ if(K1==1) { Alarm(90); Alarm(150); } } }

8、设单片机的fosc=12MHz，采用T0定时方式1在P1.0脚上输出周期为2ms的方波。 分析：1ms定时的计数初值应为：

a = 216 – t* fos / 12 = 216 – 1000* 12/ 12 = 64536 = 0xfc18 TH0 = 0xfc TL0 = 0x18 ① 查询法：

U?#include 1939XTAL1P0.0/AD038P0.1/AD137sbit P1_0=P1^0; P0.2/AD21836XTAL2P0.3/AD335void main (void) { P0.4/AD434P0.5/AD533P0.6/AD6 TMOD = 0x01; //T0定时方式1 932RSTP0.7/AD7 TR0=1; //启动T0 21P2.0/A822P2.1/A923 for( ; ; ) P2.2/A102924PSENP2.3/A113025{ TH0 = 0xfc; //装载计数初值 ALEP2.4/A123126EAP2.5/A1327P2.6/A14 TL0 = 0x18; 28P2.7/A15 while(!TF0); //查询等待TF0复位 110AP1.0P3.0/RXD211P1.1P3.1/TXD312 P1_0 =!P1_0; //定时时间到P1.0反相 BP1.2P3.2/INT0413P1.3P3.3/INT1514CP1.4P3.4/T0 TF0 = 0; //软件清TF0 615P1.5P3.5/T1716DP1.6P3.6/WR }} 817P1.7P3.7/RD②中断法： 80C51#include sbit P1_0=P1^0;

timer0 () interrupt 1 //T0中断函数 { P1_0 = !P1_0; //P1.0取反 TH0 = 0xfc; //装载计数初值

18

TL0 = 0x18; }

main ()

{ TMOD = 0x01; //T0定时方式1 TH0 = 0xfc; //装载计数初值 TL0 = 0x18; EA=1; //开总中断 ET0=1; //开T0中断 TR0=1; //启动T0

while(1); }

9、使用T1，分别用工作方式1、方式2 、方式0实现1s延时函数，晶振频率为12M.

19

C130pFX1CRYSTALC310uFR110k10、程序运行开始时先显示“00”，随后显示数值逐渐增大。待计数到59后，自动从“00”开始。 //定时中断方式实现的电子秒表

#include //51头文件

unsigned char t=0; //定义中断次数计数器 unsigned char second=0; //定义秒计数器

unsigned char code table[]={0x3f,0 …… 此处隐藏：2879字，全部文档内容请下载后查看。喜欢就下载吧 ……