netapp存储配置练习 - 图文(6)

tan> rdfile /etc/rc #Auto-generated by setup Sat Dec 19 22:53:36 GMT 2009 hostname tan ifconfig ns0 `hostname`-ns0 mediatype auto ifconfig ns1 `hostname`-ns1 mediatype auto route add default 192.168.0.1 1 routed on options dns.enable off options nis.enable off 缺省网关： Routed是一个系统启动时就启动的后台进程,这个后台进程处理进来的数据包并且周期性的去检查路由表的条目，可以用下面的命令来显示缺省网关的列表。 tan> routed status ?====显示缺省网关的列表 RIP snooping is on Gateway Metric State Time Last Heard 192.168.0.1 1 ALIVE Tue Dec 22 06:32:32 GMT 2009 0 free gateway entries, 1 used 这个命令列出了下面的信息： 是否RIP探测器活着 当前缺省网关的列表 缺省网关的跳数 网关的状态(alive还是dead)

4.3、配置和管理网络接口

Netapp存储支持下面四种网络类型： ? ? ? ?

Ethernet 10/100 BaseT Gigabit Ethernet FDDI ATM

现在应该还支持万兆以太网了。

每个接口卡的端口命名是由接口类型和插槽号合并来命名的。 下表是单口接口卡的命名示例： 网络命名规则： ? ? ?

网络类型 Slot号 Port号

多端口接口卡命名规则，下表是4端口卡命名：

/etc/sysconfigtab文件包含了什么DataONTAP版本和硬件平台支持什么类型的接口卡。 这个文件节选如下：

# This version of sysconfigtab corresponds to Data ONTAP(R) release 7.3 ?=什么DataONTAP版本 # The syntax for \# card PN type vendor dev-id sub-id description ?==标题 # ---- -- ---- ------ ------ ------ ----------- # Definitions: # PN is the marketing part number ?==PN代表销售的部件号 # # NOTE: Marketing numbers in this file may be bogus or incorrect. # Please consult the configuration guide for proper marketing numbers # for adapters. # # NOTE: If new cards are being added they need to be evaluated for # vulnerability to the Intel livelock problem. See burt#62742 for # details. Additional code may be needed in sysconfig.c for card # types A, B, or C. # Board types are arbitrarily numbered as: # 0 = motherboard # 1 = ethernet # 2 = storage host adapter (SCSI, FC, IDE/ATA) # 3 = NVRAM # 4 = FDDI # 5 = PCI bridge # 6 = ATM # 7 = Interconnect # 8 = management adapter # 9 = scsi target host adapter (FCP, iSCSI) # 10 = PCI-ISA bridge # 11 = other bridge # 12 = DAT Adaptor # 13 = Compression card # 14 = Remote I/O Interconnect card # 15 = Accelerator card # Vendor and dev-id are the Vendor ID and Device ID from the card's PCI # configuration registers. # # Sub-id is an arbitrary unique number assigned by the adapter driver to # distinguish between cards with the same vendor and device id, if # necessary. # # Cards are then identified by this tuple: dip->vid (PCI vendor ID), # dip->did (PCI device ID), dip->subid (whatever the adapter driver # sets it to, otherwise the default zero). The sysconfig checker does # not use the marketing numbers for identification. # ------------------------------------------------------------------------ version 1.000 # ------------------------------------------------------------------------ # Ethernet/GBE cards # X1026A is physically equivalent to X1025B, i.e. intel GbE II. # X1026B is physically equivalent to X1025C, i.e. intel GbE III. # ------------------------------------------------------------------------ # card PN type vendor dev-id sub-id description # ---- -- ---- ------ ------ ------ ----------- card X1005A 1 0x1425 0xb 0 Chelsio T210 TOE 10G NIC card X1007A 1 0x1425 0xd 0 Chelsio T204V TOE 4x1G NIC card X1006A 1 0x1425 0xf 0 Chelsio T204E TOE 4x1G NIC card X1008A 1 0x1425 0x31 0 Chelsio T320E TOE 2x10G NIC card X1017A 1 0x14E4 0x5822 0 IPSEC Crypto Adapter card X1001C 1 0x8086 0x1229 1 Single FastEnet-10/100 Ethernet card X1012C 1 0x8086 0x1209 2 Quad FastEnet-10/100 Ethernet card X1025B 1 0x8086 0x1000 0 Gigabit Ethernet II card X1025C 1 0x8086 0x1001 0 Gigabit Ethernet III card X1026A 1 0x8086 0x1000 0 Gigabit Ethernet II (Dell F85) card X1026B 1 0x8086 0x1001 0 Gigabit Ethernet III (Dell F85) card X1027 1 0x8086 0x1004 0 100/1000 Ethernet III card X1027B 1 0x8086 0x1008 0 10/100/1000 Ethernet IV card X1025D 1 0x8086 0x1009 0 Gigabit Ethernet IV card X1127B 1 0x8086 0x1008 1 10/100/1000 low profile Ethernet IV card X1125D 1 0x8086 0x1009 1 Gigabit low profile Ethernet IV card X1037 1 0x8086 0x1010 0 Dual 10/100/1000 Ethernet V card X1039A 1 0x8086 0x105E 0 PCI-E Dual 10/100/1000 Ethernet G20 card X1035 1 0x8086 0x1012 0 Dual Gigabit Ethernet V card X1038A 1 0x8086 0x105F 0 PCI-E Dual Gigabit Ethernet G20 card X1047 1 0x8086 0x101D 0 Quad 10/100/1000 Ethernet V card X1047B 1 0x8086 0x10B5 0 Quad 10/100/1000 Ethernet VII card X1049A 1 0x8086 0x10A4 0 PCI-E Quad 10/100/1000 Ethernet G20 card X1027C 1 0x8086 0x1026 0 10/100/1000 Ethernet VI card X1025E 1 0x8086 0x1027 0 Gigabit Ethernet VI card X1127C 1 0x8086 0x1026 1 10/100/1000 Ethernet VI, low profile card X1125E 1 0x8086 0x1027 1 Gigabit Ethernet VI, low profile card X1037B 1 0x8086 0x1079 0 Dual 10/100/1000 Ethernet VI card X1037C 1 0x8086 0x1079 2 Dual 10/100/1000 Ethernet VII card X1035B 1 0x8086 0x107a 0 Dual Gigabit Ethernet VI card X1620 1 0x135B 0x2001 0 Emulex GN9000/VI (DAFS) # ------------------------------------------------------------------------ # SCSI/FCAL Host Adapters # ------------------------------------------------------------------------ # X2016, X2016A, X2016B, X2017, X2019, X2022 are all the same, # hence they're al …… 此处隐藏：5464字，全部文档内容请下载后查看。喜欢就下载吧 ……